Ushio FTC 20W 12V 17 Degree Beam Spread MR11 Halogen Lamp

Ushio FTC Halogen MR11 LampUSHIO was established in 1964, when the use of light was just beginning to gain industrial significance, with the aim of developing illumination and energy related applications for light. Through out its history, USHIO has focused on developing new lighting technologies in cooperation with our customers. Film & Cinema Lighting, Video Lighting, Concert & Stage Lighting, Theatrical Lighting, Club and Disco Lighting, and Special Effects Lighting. SOS and USHIO have been partners since 1981 solving technical lighting challenges one customer at a time.  If you have any questions about the FTC lamp or any other specialty lighting need, please do not hesitate to give us a call.  Our staff is well trained on answering technical questions concerning any of your lighting needs.  Ushio FTC Specifications:ANSI Code: FTC Reference: JDR/M12V-20W/G/SP17 Voltage: 12 VoltsWatts: 20 Watts Base Type: GZ4 Cover Glass: No Color Temperature: 2,925 Kelvin Beam Spread: 17 Degrees (Spot) Average Life Hours: 2,000 Hours  Other Known FTC Codes: Eiko 15122, Ushio 1000619, Q20MR11/SP, GE 41890, Philips 6710, Satco FTC SOS Notes About FTC Bulb Removal and Replacement:When replacing a FTC lamp always wait for the lamp to cool down within the fixture before removing it.  Halogen lamps get extremely hot and can cause severe burning if touched while in operation or immediately afterward.  Take the lamp out by using a cloth that provides some insulation from the heat.  When removing an FTC from the fixture get as close as possible to the base before removing from the socket.  Take extra care when you take the new bulb out of the packaging and do not touch the glass bulb itself.  Touching the 'reflector" will not cause any performance issues. It is a good idea to use gloves or a cloth to insert the lamp into the FTC socket.  The oil from your skin makes the glass of the bulb itself superheat and causes early FTC lamp failure. Other Notes Concerning Halogen and Incandescent Light Bulb:

• Halogen lamps operate at extremely high temperatures that can cause serious physical injuries and property damage.

• Only use Halogen lamps in Halogen-approved fixtures. Fixtures should fully contain any parts of the Halogen lamp upon the event of a lamp burst.

• Do not use Halogen lamps in close proximity of paper, cloth or other combustible materials that can cause a fire hazard.

• Lamps are very fragile. Do not drop, crush, bend or shake them. Vibration or impact will cause filament breakage and short lamp life.

• Do not touch the Halogen bulb surface or inside reflectors with your bare hands. Oils from skin can lead to breakage or shorten the life of the lamp. Use clean gloves or lint-free cloth for installation and removal.

• Clean any dirt, oil, or lint away from the lamp with alcohol and a lint-free cloth or tissue. Any foreign particles or materials on the bulb surface can cause hot spots on the bulb and result in lamp failure.

• Never touch the lamp when it is on, or soon after it has been turned off, as it is hot and may cause serious burns.

• Do not look directly at the operating lamp for any period of time; this may cause serious eye injury.

• Always turn off the electrical power before inserting, removing, or cleaning the lamp.

• Affix the lamp securely in the socket. Improper installations will cause electrical arcing, overheating and short life to lamp and socket. Replace lamp holders and sockets when necessary.

• Keep the temperature of the Halogen lamp seal below 350° C.

• Keep the temperature of the Halogen bulb wall above 250° C.

• Keep the temperature of the Halogen lamp bulb wall below 800° C.

• Make sure lamps of specified wattage and voltage are only used in appropriately rated fixtures. Unspecified use will lead to short lamp life, breakage and overheating of fixture.

• Lamps should not be operated beyond the total rated voltage. Avoid the use of dimmers that may drive your lamp over its rated voltage.

• Operate the lamp only in the indicated burn position. Failure to do so will lead to overheating and shortened lamp life.

• Use an external fuse when required.

• Do not allow one lamp to directly expose another. This may lead to overheating and shortened lamp life.