Baja Heat 6.5 MB200 / Warrior Mini Bike TC2 Torque Converter Kit

Bike not included. Convert your Baja Heat MB200 / Warrior Minibike from a Jackshaft to a Torque Converter. The 1002 TC2 3/4" Bore, 10 Teeth, #40/41 chain, Easy to install, Bolts onto your 196cc Engine and gives you a big boost in power! IN STOCK
Visit Store
PRICE:
$189.00
at Go Karts & Mini Bikes

Product Details

BAJA HEAT 6.5   1002B TORQUE CONVERTER KIT    3/4" Bore, #40/41 Chain, 10 Tooth Sprocket, 2-7hp Engines   (MINIBIKE NOT INCLUDED)GUARANTEED IN STOCKAmazing Take-off Power and Speed for your Baja Heat 6.5, MB200 or Warrior Minibike. Convert the Jackshaft to a Torque Converter. The Baja Heat is a good minibike, but lacking in speed. This is a great upgrade!  Convert your Baja Heat (MB200) 6.5 Minibike from a Jackshaft to a Torque Converter. The 1002B TC2  3/4" Bore, 10 Teeth, #40/41 chain, Easy to install, Bolts onto your 196cc Engine and gives you a big boost in power! some minor modifications may be needed depending on model/year. Detailed Installation Instructions included. DOCUMENTATION:TC2 INSTALLATION INSTRUCTIONS GTC Website GTC Product List  NOTE: Your engine must have a Drilled and Tapped Crankshaft in order for this kit to work. WARRIOR/MB200: Please Note, this kit will install on the Warrior or MB200 minibike engine ONLY if the crankshaft is drilled and tapped for a bolt. We have noticed that some Warrior / MB200 minibikes do not have a tapped crankshaft engine. Please check your engine before ordering. All Baja Heat minibikes come with a tapped crankshaft.   OPTION:If your engine does not  have a tapped crankshaft, then you can Add one of our Titan 6.5 or Powersport Engines which will all fit well on your Baja Minibike, and will accept this torque converter kit, and has the proper throttle cable linkage. Add an Engine in Product Options above. click here to see the Titan  SAVE $55: add an engine to this kit in Product Options above and receive Free Shipping on the engine. That's $55 Off Torque Converters dramatically improve Take Off Power, Acceleration, Climbing Ability and Top End Speed on Gokarts, Minibikes and other Small Vehicles. Vehicles currently using a Centrifugal Clutch can easily upgrade to a TC2 Torque Converter GTC Website  Bench Test Video  QUALITY ASSURANCE TESTING:GokartsUSA's initial testing of the GTC Torque Converter proved highly successful. The TC2 was road tested on a Little Bad Ass Minichopper with a 5hp Tecumseh Engine. The TC2 model 1002 was used which has a 3/4" Bore and #40/41P Chain. The performance impressed our technicians. The low end power and torque was strong enough to raise the front wheel with just barely applying the throttle. Take off and acceleration was also remarkably impressive. Taking on a steep hill from a complete stop, the TC2 smoothly down shifted and pulled the 200 pound rider up the hill with ease. On level ground, at maximum throttle, the TC2 shifted into a very high overdrive ratio and gave us an impressive top speed of 52mph from this stock 5hp Tecumseh. All in all, the TC2 performed significantly better than the stock TAV2* the bike originally came with. *Note: COMET and TAV2 are trademarks of Certified Parts Corporation. GTC Industries is not affiliated or associated with Certified Parts or its products in any way NOTES:TC2 1002 is compatible with Comet* 218353A TAV2* 30-75 Torq-A-Verter    INCLUDED:The TC2 Torque Converter is a complete kit that includes both drive and driven clutches, belt, billet aluminum engine mounting plate with a built in jackshaft and sprocket, all hardware and installation instructions MODELS:Four TC2 Kit Models Available

  • 1001  3/4" Bore, #35 Chain
  • 1002  3/4" Bore, #40/41 Chain
  • 1003  1" Bore, #35 Chain
  • 1004  1" Bore, #40/41 Chain 
ENGINES:TC2 Bolts onto most engines with a horizontal shaft including:
  • Briggs
  • Robin 
  • Tecumseh
  • Honda (and clones) 
  • Kohler
  • Clinton
  • Lifan  
High PerformanceThe TC2 is a High Performance asymmetrical torque converter system in which the sheave faces have different angles. The system operates with the torque sensing cam in an outboard position allowing for in-line operation of the unit. The primary benefit of this design is that it allows proper alignment of the final drive chain to be on the same side of the vehicle as the torque converter. Moreover, the angle on the movable sheave being set at 18 degrees enables the unit to raise the belt to a larger pitch diameter with less travel of the sheave. This allows the unit to achieve higher overdrive ratios at maximum RPM

·         In-Line Operation

·         Powerful Low Ratio

·         Smooth Shifting on Load Demand

·         Infinite High  / Low Ratios

·         High Performance Overdrive

 OPERATION OF THE TC2

The TC2 provides Neutral engagement at Engine Idle. At 2200 RPM, the system engages for a Powerful Low Ratio for great takeoff speed. At Mid Range, the TC2 instantaneously shifts ratios based upon RPM and Load Requirements. Finally, the High Performance Overdrive engages for maximum speed

      TC2 Drive and Driven UnitsParts

PART#

DESCRIPTION

COMET#

1001

TC2 Torque Converter 3/4" Bore, #35P, 12T

218352A

1002

TC2 Torque Converter 3/4" Bore, #40/41P, 10T

218353A

1003

TC2 Torque Converter 1" Bore, #35P, 12T

218354A

1004

TC2 Torque Converter 1" Bore, #40/41P, 10T

218355A

1005

DRIVER UNIT 3/4"

203814A

1006

DRIVER UNIT 1"

203603A

1007

DRIVEN UNIT 5/8" BORE

217610A

1008

DRIVER MOUNTING BOLT 3/4" CRANKSHAFT

205384A

1009

DRIVER MOUNTING BOLT 1" CRANKSHAFT

215732A

1010

LOCK WASHER, 5/16

200701A

1011

PILOT WASHER 3/8

200840A

1012

PILOT WASHER 5/16

202429A

1013

DRUM DRIVER 3/4"

202090A

1014

DRUM DRIVER 1"

202427A

1015

HUB DRIVER 3/4" 4 SPLINED

203376A

1016

HUB DRIVER 1" 8 SPLINED

203641A

1017

DRIVER WEIGHT ASSY W/SPRINGS

200344A

1018

BLUE GARTER SPRING SET OF 2

011188A

1019

SHEAVE MOVABLE HALF W/HUB 3/4" BORE

200410A

1020

SHEAVE MOVABLE HALF W/HUB 1" BORE

203515A

1021

BUSHING BRONZE (NOT USED ON 1")

200349A

1023

BELT, ASYMMETRIC

203589A

1024

SHEAVE STATIONARY 3/4" BORE

202066A

1025

SHEAVE STATIONARY 1" BORE

206633A

1026

SPACER STEEL  3/4"

200389A

1027

SPACER STEEL  1"

202877A

1028

JAM NUT

203189A

1029

SNAP RING

204714A

1030

FIXED CAM

215650A

1031

SPRING GREEN

215699A

1032

FACE MOVEABLE WITH CAM

215647A

1033

BUTTON INSERT

204332A

1034

BUSHING

203942A

1035

FACE FIXED WITH POST 5/8" BORE

217612A

1036

KEY 3/16" SQ  x  2-1/4"

209831A

1037

KEY 3/16" SQ  x  9/16"

011059A

1038

JACKSHAFT, 5/8" DIAMETER

212225A

1039

WASHER 5/8"

200834A

1040

SPROCKET 12T 35P

200379A

1041

SPROCKET 10T 40/41P

102168A

1042

BALL BEARING SEALED 5/8"

215558A

1043

SPACER 5/8"

203187A

1044

SNAP RING FOR 5/8" SHAFT

212227A

1045

MOUNTING BRACKET W/BEARINGS AND SPACER

218525A

1046

ENGINE MOUNTING BOLT

217867A

1047

LOCK WASHER 5/16"

200701A

1048

SHROUD PLASTIC W/DECALS

218351A

1049

SCREW, SHROUND MOUNTING

214146A

1050

ROUND DECAL

218513A

1051

LONG DECAL

218514A

WARNING: Serious injury or death can result from improper installation or operation of this product. Children under the age of 16 should not operate vehicles with this product installed. Do not operate the TC2 without a cover, chain and belt guard device designed specifically for your vehicle (not supplied). Long hair or loose clothing can become entangled with moving parts and cause serious injury or death. Engines and moving parts can become hot and cause burns. By ordering this product, the purchaser accepts all risks associated with installation and operation of this product

Review This Product

Be the first to review this product!

Submit Your Product Reviewall fields are required
  • * 100 character minimum
  • * 4 character minimum

Similar Products From Other Merchants

MonsterMarketplace.com